Ridge Cap
In stockRidge
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop
Covers the peak where the two roof slopes meet. Both sides are the same.
Home / Products / Trim Profiles
Trim Profiles
Trim made to fit our metal panels. Pick your panel to see the trim that goes with it. Every piece comes in 10′ lengths, in the same colors as our panels, so your ridge, eaves, walls and corners match the rest of the building.
Choose your panel
10′Every trim piece
Pick a panelSee the trim that fits it
20 colorsSame as our panels
CustomFlashing made to order
Trim for 3′ Tough Rib
Panel profile
3′ Tough Rib
- Coverage36″
- Ribs3/4″, 9″ o.c.
- Gauge29 ga.
- UseRoofs & walls
Panel profile
Board & Batten
- Panel width10″
- Batten2″ wide, 3/4″ tall
- Gauge26 ga.
- UseWalls only
Panel profile
PBR Panel
- Coverage36″
- Ribs1-1/4″, 12″ o.c.
- Gauge26 ga.
- UseRoofs & walls
Panel profile
Standing Seam
- Coverage15″ or 16″
- SeamSnap lock, no clips
- Gauge26 ga.
- UseRoofs only
Our 15″ and 16″ standing seam panels both use the same trim.
PBR Panel trim is coming soon. We're adding the trim profiles for this panel. In the meantime, call or request a quote and we'll tell you what you need.
Standing Seam trim is coming soon. We're adding the trim profiles for this panel. In the meantime, call or request a quote and we'll tell you what you need.
Profile Ridge Cap
In stockVented ridge
- Flat width14″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop
A ridge cap with longer nail legs to sit over the vented closure strips.
Drip Edge
In stockEave
- Flat width5″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop and face
Goes under the panels at the eave so water drips clear of the fascia.
Endwall Flashing
Made to orderWhere a roof meets a wall
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Seals the joint where the top of a roof meets a wall, like a lean-to roof against the side of a building.
Sidewall Flashing
Made to orderWhere a roof runs along a wall
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Flashes the side of a roof where it runs along a wall, like the side of a lean-to roof.
Pitch Change Flashing
Made to orderWhere the pitch changes
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop
Flashes the line where a roof changes from one pitch to another. Bent for a 4/12 to a 2/12 pitch as standard.
W Valley
Made to orderValleys
- Flat width20″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop
Lines the valley where two roof slopes meet. The raised center rib keeps water from one slope from running across onto the other.
V Valley
Made to orderValleys
- Flat width20″
- Length10′ pieces
- Gauge29 ga.
- Painted sideTop
Lines the valley where two roof slopes meet.
Outside Corner — Large
In stockOutside corners
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Wraps the outside corners of the building where two walls meet. Same profile as the ridge cap, bent to 90°.
Outside Corner — Small
In stockOutside corners
- Flat width9-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
A smaller outside corner for the same job. Same as the large corner, with 2-1/2" sides in place of 4-1/2".
Inside Corner — Large
In stockInside corners
- Flat width13-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideInside of the corner
Finishes inside corners, like where a wall meets a lean-to or an L-shaped building. The large outside corner with the center bend reversed.
Inside Corner — Small
In stockInside corners
- Flat width9-1/2″
- Length10′ pieces
- Gauge29 ga.
- Painted sideInside of the corner
A smaller inside corner. The small outside corner with the center bend reversed.
J-Channel
In stockPanel ends, doors & windows
- Flat width5″
- Length10′ pieces
- Gauge29 ga.
- Painted sideFace
Holds the cut ends of wall panels at the top and bottom of the wall, and around doors and windows.
Small Rat Guard
Made to orderBottom of the wall panels
- Flat width4-7/8″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Closes off the open ribs at the bottom of the wall panels to keep rodents and birds out.
Large Rat Guard
Made to orderBottom of the wall panels
- Flat width5-3/4″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
A larger rat guard with a longer angled leg, for closing off the open ribs at the bottom of the wall panels.
Drip Mold
Made to orderDoors, windows & concrete aprons
- Flat width5″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Sheds water away from the tops of doors and windows and protects panels where they meet concrete aprons. Won’t collect debris like J-channel.
Bottom Trim
Made to orderBase of the building & wainscot
- Flat width5″
- Length10′ pieces
- Gauge29 ga.
- Painted sideOutside
Flashes the panels around the base of the building and works as a transition for wainscot panels.
Custom Trim
Made to orderAny profile you need
Don't see the profile you need? We can make it. Send us a sketch with your measurements, colors and how many pieces, and we'll quote it. Custom trim comes in 10′ lengths.